Short answer: to turn the mass of a peptide into a concentration you need three numbers: the mass you weighed or were supplied, the molecular weight of the peptide, and the volume of solvent. Divide mass by molecular weight to get moles, then divide moles by volume to get molar concentration. This guide walks through that arithmetic with worked examples, explains why “net peptide content” can change the answer, and lists the unit mistakes that cause most laboratory errors. It is written for laboratory work and uses concentrations, not doses. It is designed to be read alongside our peptide calculator, which does the same calculation in a form.
Why careful arithmetic matters in peptide research
A surprising proportion of irreproducible results in small-molecule and peptide work comes down to concentration errors, not biology. Peptides are supplied in small amounts, usually milligrams, and the volumes involved are often microlitres. A misplaced decimal or a milligram-versus-microgram confusion turns a plausible experiment into a meaningless one, and the error can be invisible in the data.
Good practice is simple and unglamorous. Write the calculation down, state the units at every step, check the answer against a rough estimate, and keep the record with the experiment. The rest of this guide shows the steps. Our guide to laboratory handling of lyophilised peptides covers the practical side of preparing solutions, and this article sticks to the maths.
The four quantities you need
- Mass (m): how much peptide you have, in milligrams or micrograms.
- Molecular weight (MW): the mass of one mole of the peptide, in grams per mole (g/mol, equivalent to Da). It is printed on the certificate of analysis and the product page.
- Volume (V): the volume of solvent in which the peptide will be dissolved, in millilitres or microlitres.
- Concentration (C): the result, as mass per volume (mg/mL) or amount per volume (mM, µM).
Two relationships do most of the work: moles = mass ÷ molecular weight, and concentration = moles ÷ volume. Everything else is unit conversion.
Worked example 1: from mass to millimolar
Suppose a vial contains 5 mg of a peptide with a molecular weight of 1,000 g/mol, and you dissolve it in 2 mL of solvent.
1. Convert mass to grams: 5 mg = 0.005 g. 2. Moles = 0.005 g ÷ 1,000 g/mol = 0.000005 mol = 5 µmol. 3. Volume in litres: 2 mL = 0.002 L. 4. Concentration = 5 µmol ÷ 0.002 L = 2,500 µM = 2.5 mM.
As a check, 5 mg in 2 mL is 2.5 mg/mL. A 1,000 g/mol peptide at 2.5 mg/mL is 2.5 mM, because 1 mg/mL of a 1,000 g/mol peptide is 1 mM. That shortcut, mg/mL ÷ MW (in kDa) = mM, is a useful sanity check for any peptide.
Worked example 2: planning a dilution with C1V1 = C2V2
Often you do not use a stock directly. You dilute it. The relationship C1 × V1 = C2 × V2 holds as long as you are only adding solvent.
Take the 2.5 mM stock above and suppose an experiment needs 500 µL of a 100 µM working solution.
1. C1 = 2,500 µM, C2 = 100 µM, V2 = 500 µL. 2. V1 = (C2 × V2) ÷ C1 = (100 × 500) ÷ 2,500 = 20 µL. 3. Add 20 µL of stock to 480 µL of solvent.
The check is the dilution factor: 2,500 ÷ 100 = 25, and 500 ÷ 25 = 20. If the two routes give the same number, the arithmetic is right.
Worked example 3: a serial dilution
When a range of concentrations is needed, a serial dilution is more accurate than preparing every tube from the stock, because small pipetting volumes carry larger relative error. A two-fold or ten-fold series is standard.
For a ten-fold series starting at 100 µM: transfer 100 µL of the 100 µM solution into 900 µL of solvent to give 10 µM; repeat to give 1 µM, 0.1 µM and so on. Record the starting concentration, the transfer volume, the diluent volume and the mixing step for each tube. Errors compound along a series, so keep pipettes calibrated and mix thoroughly at each step.
Net peptide content: why mass on the label is not always peptide
This is the most commonly forgotten factor. The weight in a vial is the gross weight of the lyophilised powder. That powder contains peptide, but also counter-ions from purification (for example acetate or trifluoroacetate) and residual water. The fraction that is actually peptide is the net peptide content, and it is often noticeably below 100%.
Do not confuse net peptide content with purity. HPLC purity tells you what proportion of the *peptide material* is the target sequence rather than related impurities. Aguilar (Methods in Molecular Biology, 2004) gives a good account of how HPLC separates and quantifies peptides, which is the method behind most purity figures. Net peptide content is a separate measurement, often by amino acid analysis or elemental analysis, and a certificate may or may not report it.
If the certificate states a net peptide content, correct for it:
- active mass = gross mass × net peptide content (as a fraction), then use active mass in the calculation above.
- Example: 5 mg gross at 80% net content gives 4 mg of peptide, which in 2 mL is 2 mg/mL, or 2 mM for a 1,000 g/mol peptide, not 2.5 mM.
If the certificate does not state it, say in your records that the calculation uses gross mass and treat the concentration as an upper bound. For comparative experiments where relative differences matter, that may be acceptable; for absolute quantitation, ask the supplier or measure it.
Units and the usual mistakes
Most errors are one of the same few kinds.
- mg versus µg. A thousand-fold slip. Write units next to every number.
- mL versus µL. Another thousand-fold slip. Convert everything to litres or to one consistent unit before dividing.
- Molecular weight of the wrong form. The MW of the free peptide differs from the salt. Use the value the certificate quotes and note which form it refers to.
- Forgetting the diluent in C1V1. The formula assumes that V2 is the final total volume, so V1 plus the diluent must equal V2.
- Rounding too early. Keep extra digits through the calculation and round the final answer.
- Mixing mass and molar concentrations. A 1 mg/mL solution of a 500 g/mol peptide is 2 mM, but of a 5,000 g/mol peptide it is 0.2 mM. Always state which scale you are using.
What stability adds to the picture
A calculated concentration is true on the day you prepare it. Peptides in solution can adsorb to plastic, oxidise, aggregate or hydrolyse, so a stock that was 2.5 mM when made may not be 2.5 mM a week later. General principles on how biological molecules degrade are reviewed in Manning et al. (Pharmaceutical Research, 2010). For practical purposes, record the preparation date, solvent, storage temperature and freeze-thaw count, and prepare fresh solutions for sensitive experiments. The certificate and supplier notes for your specific compound should guide solvent choice and storage; there is no universal rule.
Using the calculator
The peptide calculator on this site automates the steps in examples 1 and 2 so that you can check a hand calculation. It is designed for laboratory concentration planning and does not give guidance on use in people. For compounds with specific handling notes, such as glutathione, which oxidises readily, the product page and certificate come first. Our companion guide on the redox pair involved, NAD and glutathione, shows why preparation and storage conditions matter in practice. All batches from Peptides Lab UK are HPLC & COA Verified, so the molecular weight and purity you need for these calculations are on the certificate that matches your vial.
Frequently asked questions
For the supplier-evidence side of this topic, see our best research peptides UK checklist and our guide to where to buy peptides in the UK.
How do I calculate peptide concentration?
Divide the mass of peptide by its molecular weight to get moles, then divide by the solvent volume. For example, 5 mg of a 1,000 g/mol peptide is 5 µmol; in 2 mL that is 2.5 mM, or 2.5 mg/mL.
What is net peptide content and why does it matter?
It is the fraction of the powder that is actually peptide, as opposed to counter-ions and water. If a certificate reports 80% net content, 5 mg gross contains 4 mg of peptide, and the concentration you calculate should reflect that.
Is purity the same as net peptide content?
No. HPLC purity describes how much of the peptide material is the target sequence. Net peptide content describes how much of the powder is peptide at all.
How do I use C1V1 = C2V2?
Use it when diluting a stock with solvent only. V1 = (C2 × V2) ÷ C1. For a 2.5 mM stock and 500 µL of a 100 µM solution, V1 is 20 µL, made up to 500 µL with solvent.
Does the peptide calculator give guidance on use in people?
No. It is a laboratory concentration and dilution tool. Peptides Lab UK products are for research use only.
Peptides Lab UK products are supplied for laboratory research use only, not for human or veterinary use. This article is educational arithmetic for laboratory work and is not medical advice.